Displaying similar documents to “Robust dynamic output feedback fault-tolerant control for Takagi-Sugeno fuzzy systems with interval time-varying delay via improved delay partitioning approach”

Robust sensor fault estimation for descriptor-LPV systems with unmeasurable gain scheduling functions: application to an anaerobic bioreactor

Francisco-Ronay López-Estrada, Jean-Christophe Ponsart, Didier Theilliol, Carlos-Manuel Astorga-Zaragoza, Jorge-Luis Camas-Anzueto (2015)

International Journal of Applied Mathematics and Computer Science

Similarity:

This paper addresses the design of a state estimation and sensor fault detection, isolation and fault estimation observer for descriptor-linear parameter varying (D-LPV) systems. In contrast to where the scheduling functions depend on some measurable time varying state, the proposed method considers the scheduling function depending on an unmeasurable state vector. In order to isolate, detect and estimate sensor faults, an augmented system is constructed by considering faults to be auxiliary...

Systematic fault tolerant control based on adaptive Thau observer estimation for quadrotor UAVs

Zhaohui Cen, Hassan Noura, Younes Al Younes (2015)

International Journal of Applied Mathematics and Computer Science

Similarity:

A systematic fault tolerant control (FTC) scheme based on fault estimation for a quadrotor actuator, which integrates normal control, active and passive FTC and fault parking is proposed in this paper. Firstly, an adaptive Thau observer (ATO) is presented to estimate the quadrotor rotor fault magnitudes, and then faults with different magnitudes and time-varying natures are rated into corresponding fault severity levels based on the pre-defined fault-tolerant boundaries. Secondly, a...

Fault-tolerant control strategy for actuator faults using LPV techniques: Application to a two degree of freedom helicopter

Saúl Montes de Oca, Vicenç Puig, Marcin Witczak, Łukasz Dziekan (2012)

International Journal of Applied Mathematics and Computer Science

Similarity:

In this paper, a Fault Tolerant Control (FTC) strategy for Linear Parameter Varying (LPV) systems that can be used in the case of actuator faults is proposed. The idea of this FTC method is to adapt the faulty plant instead of adapting the controller to the faulty plant. This approach can be seen as a kind of virtual actuator. An integrated FTC design procedure for the fault identification and fault-tolerant control schemes using LPV techniques is provided as well. Fault identification...

Actuator fault diagnosis for flat systems: A constraint satisfaction approach

Ramatou Seydou, Tarek Raissi, Ali Zolghadri, Denis Efimov (2013)

International Journal of Applied Mathematics and Computer Science

Similarity:

This paper describes a robust set-membership-based Fault Detection and Isolation (FDI) technique for a particular class of nonlinear systems, the so-called flat systems. The proposed strategy consists in checking if the expected input value belongs to an estimated feasible set computed using the system model and the derivatives of the measured output vector. The output derivatives are computed using a numerical differentiator. The set-membership estimator design for the input vector...

Observer-based adaptive sliding mode fault-tolerant control for the underactuated space robot with joint actuator gain faults

Ronghua Lei, Li Chen (2021)

Kybernetika

Similarity:

An adaptive sliding mode fault-tolerant controller based on fault observer is proposed for the space robots with joint actuator gain faults. Firstly, the dynamic model of the underactuated space robot is deduced combining conservation law of linear momentum with Lagrange method. Then, the dynamic model of the manipulator joints is obtained by using the mathematical operation of the block matrices, hence the measurement of the angular acceleration of the base attitude can be omitted....

Supervisory fault tolerant control with integrated fault detection and isolation: A switched system approach

Hao Yang, Bin Jiang, Vincent Cocquempot, Lingli Lu (2012)

International Journal of Applied Mathematics and Computer Science

Similarity:

This paper focuses on supervisory fault tolerant control design for a class of systems with faults ranging over a finite cover. The proposed framework is based on a switched system approach, and relies on a supervisory switching within a family of pre-computed candidate controllers without individual fault detection and isolation schemes. Each fault set can be accommodated either by one candidate controller or by a set of controllers under an appropriate switching law. Two aircraft examples...

Active fault tolerant control of nonlinear systems: The cart-pole example

Marcello Bonfè, Paolo Castaldi, Nicola Mimmo, Silvio Simani (2011)

International Journal of Applied Mathematics and Computer Science

Similarity:

This paper describes the design of fault diagnosis and active fault tolerant control schemes that can be developed for nonlinear systems. The methodology is based on a fault detection and diagnosis procedure relying on adaptive filters designed via the nonlinear geometric approach, which allows obtaining the disturbance de-coupling property. The controller reconfiguration exploits directly the on-line estimate of the fault signal. The classical model of an inverted pendulum on a cart...

Robust fault detection of singular LPV systems with multiple time-varying delays

Amir Hossein Hassanabadi, Masoud Shafiee, Vicenç Puig (2016)

International Journal of Applied Mathematics and Computer Science

Similarity:

In this paper, the robust fault detection problem for LPV singular delayed systems in the presence of disturbances and actuator faults is considered. For both disturbance decoupling and actuator fault detection, an unknown input observer (UIO) is proposed. The aim is to compute a residual signal which has minimum sensitivity to disturbances while having maximum sensitivity to faults. Robustness to unknown inputs is formulated in the sense of the H∞ -norm by means of the bounded real...

Supervisory fault tolerant control of the GTM UAV using LPV methods

Tamás Péni, Báltin Vanek, Zoltán Szabó, József Bakor (2015)

International Journal of Applied Mathematics and Computer Science

Similarity:

A multi-level reconfiguration framework is proposed for fault tolerant control of over-actuated aerial vehicles, where the levels indicate how much authority is given to the reconfiguration task. On the lowest, first level the fault is accommodated by modifying only the actuator/sensor configuration, so the fault remains hidden from the baseline controller. A dynamic reallocation scheme is applied on this level. The allocation mechanism exploits the actuator/sensor redundancy available...

Fault diagnosis of networked control systems

Christophe Aubrun, Dominique Sauter, Joseph Yamé (2008)

International Journal of Applied Mathematics and Computer Science

Similarity:

Networked Control Systems (NCSs) deal with feedback control systems with loops closed via data communication networks. Control over a network has many advantages compared with traditionally controlled systems, such as a lower implementation cost, reduced wiring, simpler installation and maintenance and higher reliability. Nevertheless, the networkinduced delay, packet dropout, asynchronous behavior and other specificities of networks will degrade the performance of closed-loop systems....

Sliding mode methods for fault detection and fault tolerant control with application to aerospace systems

Christopher Edwards, Halim Alwi, Chee Pin Tan (2012)

International Journal of Applied Mathematics and Computer Science

Similarity:

Sliding mode methods have been historically studied because of their strong robustness properties with regard to a certain class of uncertainty, achieved by employing nonlinear control/injection signals to force the system trajectories to attain in finite time a motion along a surface in the state-space. This paper will consider how these ideas can be exploited for fault detection (specifically fault signal estimation) and subsequently fault tolerant control. It will also describe applications...