Displaying similar documents to “An SFDI observer-based scheme for a general aviation aircraft”

Detection and accommodation of second order distributed parameter systems with abrupt changes in input term: stability and adaptation

Michael A. Demetriou, Marios M. Polycarpou (1998)

Kybernetika

Similarity:

In this note, we employ nonlinear on-line parameter estimation methods based on adaptive neural network approximators for detecting changes due to actuator faults in a class of second order distributed parameter systems. The motivating example is a cantilevered beam actuated via a pair of piezoceramic patches. We examine changes in the control input term, which provide a simple and practical model of actuator failures. Using Lyapunov redesign methods, a stable learning scheme for fault...

Robust nonlinear observer design for actuator fault detection in diesel engines

Boulaid Boulkroune, Issam Djemili, Abdel Aitouche, Vincent Cocquempot (2013)

International Journal of Applied Mathematics and Computer Science

Similarity:

This paper is concerned with actuator fault detection in nonlinear systems in the presence of disturbances. A nonlinear unknown input observer is designed and the output estimation error is used as a residual for fault detection. To deal with the problem of high Lipschitz constants, a modified mean-value theorem is used to express the nonlinear error dynamics as a convex combination of known matrices with time-varying coefficients. Moreover, the disturbance attenuation is performed using...

Actuator fault diagnosis for flat systems: A constraint satisfaction approach

Ramatou Seydou, Tarek Raissi, Ali Zolghadri, Denis Efimov (2013)

International Journal of Applied Mathematics and Computer Science

Similarity:

This paper describes a robust set-membership-based Fault Detection and Isolation (FDI) technique for a particular class of nonlinear systems, the so-called flat systems. The proposed strategy consists in checking if the expected input value belongs to an estimated feasible set computed using the system model and the derivatives of the measured output vector. The output derivatives are computed using a numerical differentiator. The set-membership estimator design for the input vector...

Active fault tolerant control of nonlinear systems: The cart-pole example

Marcello Bonfè, Paolo Castaldi, Nicola Mimmo, Silvio Simani (2011)

International Journal of Applied Mathematics and Computer Science

Similarity:

This paper describes the design of fault diagnosis and active fault tolerant control schemes that can be developed for nonlinear systems. The methodology is based on a fault detection and diagnosis procedure relying on adaptive filters designed via the nonlinear geometric approach, which allows obtaining the disturbance de-coupling property. The controller reconfiguration exploits directly the on-line estimate of the fault signal. The classical model of an inverted pendulum on a cart...

Fault diagnosis and fault tolerant control using set-membership approaches: Application to real case studies

Vicenç Puig (2010)

International Journal of Applied Mathematics and Computer Science

Similarity:

This paper reviews the use of set-membership methods in fault diagnosis (FD) and fault tolerant control (FTC). Setmembership methods use a deterministic unknown-but-bounded description of noise and parametric uncertainty (interval models). These methods aims at checking the consistency between observed and predicted behaviour by using simple sets to approximate the exact set of possible behaviour (in the parameter or the state space). When an inconsistency is detected between the measured...

A double window state observer for detection and isolation of abrupt changes in parameters

Jędrzej Byrski, Witold Byrski (2016)

International Journal of Applied Mathematics and Computer Science

Similarity:

The paper presents a new method for diagnosis of a process fault which takes the form of an abrupt change in some real parameter of a time-continuous linear system. The abrupt fault in the process real parameter is reflected in step changes in many parameters of the input/output model as well as in step changes in canonical state variables of the system. Detection of these state changes will enable localization of the faulty parameter in the system. For detecting state changes, a special...

Sliding mode methods for fault detection and fault tolerant control with application to aerospace systems

Christopher Edwards, Halim Alwi, Chee Pin Tan (2012)

International Journal of Applied Mathematics and Computer Science

Similarity:

Sliding mode methods have been historically studied because of their strong robustness properties with regard to a certain class of uncertainty, achieved by employing nonlinear control/injection signals to force the system trajectories to attain in finite time a motion along a surface in the state-space. This paper will consider how these ideas can be exploited for fault detection (specifically fault signal estimation) and subsequently fault tolerant control. It will also describe applications...

Nonlinear model predictive control of a boiler unit: A fault tolerant control study

Krzysztof Patan, Józef Korbicz (2012)

International Journal of Applied Mathematics and Computer Science

Similarity:

This paper deals with a nonlinear model predictive control designed for a boiler unit. The predictive controller is realized by means of a recurrent neural network which acts as a one-step ahead predictor. Then, based on the neural predictor, the control law is derived solving an optimization problem. Fault tolerant properties of the proposed control system are also investigated. A set of eight faulty scenarios is prepared to verify the quality of the fault tolerant control. Based of...

Fault-tolerant control strategy for actuator faults using LPV techniques: Application to a two degree of freedom helicopter

Saúl Montes de Oca, Vicenç Puig, Marcin Witczak, Łukasz Dziekan (2012)

International Journal of Applied Mathematics and Computer Science

Similarity:

In this paper, a Fault Tolerant Control (FTC) strategy for Linear Parameter Varying (LPV) systems that can be used in the case of actuator faults is proposed. The idea of this FTC method is to adapt the faulty plant instead of adapting the controller to the faulty plant. This approach can be seen as a kind of virtual actuator. An integrated FTC design procedure for the fault identification and fault-tolerant control schemes using LPV techniques is provided as well. Fault identification...